# Cone

A **cone** is a three-dimensional geometric shape that tapers smoothly from a flat base (frequently, though not necessarily, circular) to a point called the apex or vertex.

A cone is formed by a set of line segments, half-lines, or lines connecting a common point, the apex, to all of the points on a base that is in a plane that does not contain the apex. Depending on the author, the base may be restricted to be a circle, any one-dimensional quadratic form in the plane, any closed one-dimensional figure, or any of the above plus all the enclosed points. If the enclosed points are included in the base, the cone is a solid object; otherwise it is a two-dimensional object in three-dimensional space. In the case of a solid object, the boundary formed by these lines or partial lines is called the *lateral surface*; if the lateral surface is unbounded, it is a conical surface.

In the case of line segments, the cone does not extend beyond the base, while in the case of half-lines, it extends infinitely far. In the case of lines, the cone extends infinitely far in both directions from the apex, in which case it is sometimes called a **double cone**. Either half of a double cone on one side of the apex is called a *nappe*.

The axis of a cone is the straight line (if any), passing through the apex, about which the base (and the whole cone) has a circular symmetry.

In common usage in elementary geometry, cones are assumed to be **right circular**, where *circular* means that the base is a circle and *right* means that the axis passes through the centre of the base at right angles to its plane.^{[1]} If the cone is right circular the intersection of a plane with the lateral surface is a conic section. In general, however, the base may be any shape^{[2]} and the apex may lie anywhere (though it is usually assumed that the base is bounded and therefore has finite area, and that the apex lies outside the plane of the base). Contrasted with right cones are oblique cones, in which the axis passes through the centre of the base non-perpendicularly.^{[3]}

Depending on the context, "cone" may also mean specifically a convex cone or a projective cone.

The perimeter of the base of a cone is called the "directrix", and each of the line segments between the directrix and apex is a "generatrix" or "generating line" of the lateral surface. (For the connection between this sense of the term "directrix" and the directrix of a conic section, see Dandelin spheres.)

The "base radius" of a circular cone is the radius of its base; often this is simply called the radius of the cone. The aperture of a right circular cone is the maximum angle between two generatrix lines; if the generatrix makes an angle *θ* to the axis, the aperture is 2*θ*.

A cone with a region including its apex cut off by a plane is called a "truncated cone"; if the truncation plane is parallel to the cone's base, it is called a frustum.^{[1]} An "elliptical cone" is a cone with an elliptical base.^{[1]} A "generalized cone" is the surface created by the set of lines passing through a vertex and every point on a boundary (also see visual hull).

The center of mass of a conic solid of uniform density lies one-quarter of the way from the center of the base to the vertex, on the straight line joining the two.

The circular sector obtained by unfolding the surface of one nappe of the cone has:

In the Cartesian coordinate system, an *elliptic cone* is the locus of an equation of the form^{[7]}

Obviously, any right circular cone contains circles. This is also true, but less obvious, in the general case (see circular section).

The intersection of an elliptic cone with a concentric sphere is a spherical conic.

In projective geometry, a cylinder is simply a cone whose apex is at infinity.^{[8]} Intuitively, if one keeps the base fixed and takes the limit as the apex goes to infinity, one obtains a cylinder, the angle of the side increasing as arctan, in the limit forming a right angle. This is useful in the definition of degenerate conics, which require considering the cylindrical conics.

According to G. B. Halsted, a cone is generated similarly to a Steiner conic only with a projectivity and axial pencils (not in perspective) rather than the projective ranges used for the Steiner conic:

"If two copunctual non-costraight axial pencils are projective but not perspective, the meets of correlated planes form a 'conic surface of the second order', or 'cone'."^{[9]}

The definition of a cone may be extended to higher dimensions (see convex cones). In this case, one says that a convex set *C* in the real vector space **R**^{n} is a cone (with apex at the origin) if for every vector *x* in *C* and every nonnegative real number *a*, the vector *ax* is in *C*.^{[2]} In this context, the analogues of circular cones are not usually special; in fact one is often interested in *polyhedral cones*.